Amundsen
Hobby
Telefon 22 38 26 29
vamunds@online.no
Trondheimsveien 84, 0565 Oslo
Hverdager 10:00 - 17:00, lørdag 10:00-15:00
Du har ingen varer i handlekurven
Tøm handlekurven
Gå til kassen
Hjem
Kjøpsbetingelser
Avansert søk
Kategorier:
TILBUD
Abteilung502
ACADEMY
AIRFIX
AK INTERACTIVE
AMT
AOSHIMA
Brawa
Busch
CARSON RC
Die-Cast Modellbiler
DRAGON
DUSEK
ESU
· Digitalutstyr
· UTSTYR
EVERGREEN
Faller H0
Fleischmann H0
FUJIMI
G-Skala
Hasegawa
HELLER
HOBBYBOSS
HOBBYZONE
HUMBROL
ICM
ITALERI
Kataloger og litteratur
KIBRI
LINDBERG
MASTER BOX
MENG
MERIT
MINIART
MONOGRAM
MPC
Märklin H0
Märklin nyheter 2020
Märklin nyheter 2021
Märklin nyheter 2022
Märklin nyheter 2023
N skala
Noch H0
Norske modeller H0
POCHER
Preiser
REVELL
Roco H0
SCHUCO MODELLBILER
SPARMAX AIRBRUSHUTSTYR
Spor 1
Tamiya
THUNDER MODEL
Trix H0
Trumpeter
Vallejo
Verktøy
Viessmann
Vollmer H0
Wiking H0 biler
Z skala
ZVEZDA
Produsenter:
Abteilung502
ACADEMY
AIRFIX
AK INTERACTIVE
AMT
AOSHIMA
Busch
DRAGON
ESU
EVERGREEN
Faller
Fleischmann
FUJIMI
Hasegawa
HELLER
HOBBYBOSS
HOBBYZONE
Humbrol
ICM
Italeri
Kibri
Kyosho
LINDBERG
Märklin
MASTER BOX
MENG
Merit
Mondo Motors
MPC
Noch
POLA
Preiser
Revell
Roco
Rokuhan
Schuco
SPARMAX
Tamiya
THUNDER MODEL
Trix
Trumpeter
Ukategorisert
Vallejo
Viessmann
Vollmer
Welly
Wiking
Yat Ming
ZVEZDA
LokPilot micro V4.0,MED LEDNING+PLUGG
Varenr: ESU 54683
Siden:
06.06.2011
Produktet finnes i kategorien(e):
ESU-Digitalutstyr
Vis ESU hjemmeside
List alle ESU produkter
LokPilot micro V4.0,MED LEDNING+PLUGG.
The LokPilot micro V4.0 is a genuine power house. It drives the loco motor with a continuous load capability of 0.75A and has significantly shrunk compared to its forerunner: the smallest member of the LokPilot V4.0 family has now a size of only 10.5mm x 8.1mm x 2.8mm and should thus fit in the smallest N-/TT-gauge locos.
LokPilot micro V4.0 decoders are available in all common plug and interface versions such as 6-pin NEM651 (with or without cable harness), 8-pin NEM652 or the brand-new wirless Next18 interface version.
Operational modes
The LokPilot micro V4.0 commands Motorola® and Selectrix® as well as DCC through 14, 28 and 128 speed steps or can be used on analogue DC layouts. You can either use 2- or 3-digit (1 – 127) as well as 4-digit (1–9999) addresses or assign a consist address.
The Motorola® protocol enables the decoder to run with Märklin® stations 6020®, 6021®, Delta®, mobile station® and Central Station®. The decoders can command addresses 01 – 255. A second address allows to switch F5 to F8, if desired.
Since the LokPilot V4.0 decoders also speaks Selectrix® it can be operated with this proven system as well.
It supports Lenz® LG 100 resp. Roco® braking sections as well as Zimo®’s HLU-commands, or the braking in DC braking sections with reversed polarity, or the Märklin® braking section (even for DCC). But also the new Lenz® ABC brake modules with an asymmetrical DCC signal is supported.
Of course, our top-class decoder is able to calculate a constant braking distance to stop your locos correctly in front of the red signal regardless of the speed. LokPilot V4.0 decoders can also be used for analogue DC or AC layouts.
The LokPilot micro V4.0 converts during operation fully automatically between all control modes (Motorola®, DCC, DC, AC and Selectrix®). That is important if some parts of your layout are operated in analogue mode (e.g. fiddle yards).
Produktet er utsolgt, og ikke lenger tilgjengelig.
Alle priser med mva.