ESU 51822 - SwitchPilot SERVO V.2

Amundsen Hobby

Telefon 22 38 26 29

vamunds@online.no

Trondheimsveien 84, 0565 Oslo

Hverdager 10:00 - 17:00, lørdag 10:00-15:00

Du har ingen varer i handlekurven

Tøm handlekurven Gå til kassen

Kategorier:

ESU

· Digitalutstyr

· UTSTYR

Produsenter:

SwitchPilot SERVO V.2
Varenr: ESU 51822
Siden: 20.06.2014
Produktet finnes i kategorien(e): ESU-Digitalutstyr
Vis ESU hjemmeside
List alle ESU produkter

SwitchPilot SERVO V.2. Modes of operation The SwitchPilot Servo can be used with DCC or Motorola® protocols. It is compatible with the DCC norm and reacts to switch commands. It is possible to operate turnouts from 01 to 508 under Motorola® use. Recognition of control mode is fully automatic. Functions The SwitchPilot Servo is being powered either directly by the digital central station itself or separately by a DC- or AC source (transformer). RC servos or ESU servo motors can be directly connected to its four servo outputs. The 5V voltage needed as well as the special control impulse is generated by the SwitchPilot Servo itself. For each servo, not only lever speed can be adjusted individually but also its end positions. Thus it is possible to operate especially prototypically slow and powerful turnout motors, independent of track- and gauge systems. You could also employ the SwitchPilot Servo for driving signal arms or railway crossings. Also the automatic opening of engine shed doors does not need to remain a dream. Programming The SwitchPilot Servo can be programmed especially comfortably: For one it supports all DCC modes of programming including POM (programming in the main). Assuming a command station with an outlet for a programming track, all adjustments can be controlled and modified. As RailCom® is integrated, it is also possible to read out and control recent settings, even during operation. Alternatively you can use the comfortable three-button input: You are able to control addresses, the end positions of all four servos and the corresponding motion speed directly, during operation and without any complicated programming- at all command stations! Analog operation The Switch Pilot Servo would not be a typical ESU product, if it had not even more to offer: You can operate the decoder without the use of a command station! Conventional switches can be controlled with the help of eight switch inputs. Therefore fans of “classic” analog model railway can benefit from the advantages of the servo motor. In other words: the SwitchPilot Servo does not need a command station to switch and set servo paths as well as speed. SwitchPilot Extension Do you need some relay outputs in addition to the servo outputs, since you intend to polarize the frog, for instance, or switch off the track voltage within the signal line section? Then you should extend your SwitchPilot Servo with the SwitchPilot Extension relay module: one of its four twin-relay contacts switches simultaneously to the servo and can be used for potential-free load swichting – ideal for tricky circuitry! Protection As it has been the case with our loco decoders, in the design phase´s greatest emphasis has been placed upon near indestructibility of the SwitchPilot Servo decoders. That means ESU quality is also built into our stationary decoders, now and in the future! You can rely on it! Future proof The internal software of the SwitchPilot Servo V2.0 can be replaced by a more up-to-date version at any time. This is done with the aid of the ESU LokProgrammer. That way everything remains current in case of changes in the standards and you may also profit from new functions.

kr 390	Antall:

De som kjøpte overstående produkt kjøpte også

SERVOMOTOR
Varenr: ESU 51804
Siden: 18.03.2010

SERVOMOTOR
kr 200
Info

Kontrollpult
Varenr: 72720
Siden: 22.02.2004

Kontrollpult for penser og signaler
kr 290
Info

HÅNDDRILL 0,1-3,2 mm
Varenr: TA 74050
Siden: 03.08.2009

HÅNDDRILL 0,1-3,2 mm
kr 260
Info

Alle priser med mva.